The Full Wiki

Analog electronics: Wikis

Note: Many of our articles have direct quotes from sources you can cite, within the Wikipedia article! This article doesn't yet, but we're working on it! See more info or our list of citable articles.


(Redirected to Analogue electronics article)

From Wikipedia, the free encyclopedia

Analogue electronics (or analog in American English) are those electronic systems with a continuously variable signal. In contrast, in digital electronics signals usually take only two different levels. The term "analogue" describes the proportional relationship between a signal and a voltage or current that represents the signal. The word analogue is derived from the Greek word ανάλογος (analogos) meaning "proportional".[1]


Analogue signals

An analogue signal uses some attribute of the medium to convey the signal's information. For example, an aneroid barometer uses the angular position of a needle as the signal to convey the information of changes in atmospheric pressure.[2] Electrical signals may represent information by changing their voltage, current, frequency, or total charge. Information is converted from some other physical form ( such as sound, light, temperature, pressure, position) to an electrical signal by a transducer which converts one type of energy into another e. g. a microphone.[3]

The signals take any value from a given range, and each unique signal value represents different information. Any change in the signal is meaningful, and each level of the signal represents a different level of the phenomenon that it represents. For example, suppose the signal is being used to represent temperature, with one volt representing one degree Celsius. In such a system 10 volts would represent 10 degrees, and 10.1 volts would represent 10.1 degrees.

Another method of conveying an analogue signal is to use modulation. In this, some base carrier signal has one of its properties altered: amplitude modulation (AM) involves altering the amplitude of a sinusoidal voltage waveform by the source information, frequency modulation (FM) changes the frequency. Other techniques, such as phase modulation or changing the phase of the carrier signal, are also used.[4]

In an analogue sound recording, the variation in pressure of a sound striking a microphone creates a corresponding variation in the current passing through it or voltage across it. An increase in the volume of the sound causes the fluctuation of the current or voltage to increase proportionally while keeping the same waveform or shape.

Mechanical, pneumatic, hydraulic and other systems may also use analogue signals.

Inherent noise

Analogue systems invariably include noise; that is, random disturbances or variations, some caused by the random thermal vibrations of atomic particles. Since all variations of an analogue signal are significant, any disturbance is equivalent to a change in the original signal and so appears as noise. [5] As the signal is copied and re-copied, or transmitted over long distances, these random variations become more significant and lead to signal degradation. Other sources of noise may come from external electrical signals, or poorly designed components. These disturbances are reduced by shielding, and using low-noise amplifiers (LNA).[6]

Analogue vs. digital electronics

Since the information is encoded differently in analogue and digital electronics, the way they process a signal is consequently different. All operations that can be performed on an analogue signal such as amplification, filtering, limiting, and others, can also be duplicated in the digital domain.

The first electronic devices invented and mass produced were analogue. The use of microelectronics has reduced the cost of digital techniques and now make digital methods feasible and cost-effective such as in the field of human-machine communication by voice.[7]

The main differences between analogue and digital electronics are listed below:


Because of the way information is encoded in analogue circuits, they are much more susceptible to noise than digital circuits, since a small change in the signal can represent a significant change in the information present in the signal and can cause the information present to be lost. Since digital signals take on one of only two different values, a disturbance would have to be about one-half the magnitude of the digital signal to cause an error; this property of digital circuits can be exploited to make signal processing noise-resistant. In digital electronics, because the information is quantized, as long as the signal stays inside a range of values, it represents the same information. Digital circuits use this principle to regenerate the signal at each logic gate, lessening or removing noise.[8]


A number of factors affect how precise a signal is, mainly the noise present in the original signal and the noise added by processing. See signal-to-noise ratio. Fundamental physical limits such as the shot noise in components limits the resolution of analogue signals. In digital electronics additional precision is obtained by using additional digits to represent the signal; the practical limit in the number of digits is determined by the performance of the analog-to-digital converter(ADC), since digital operations can usually be performed without loss of precision. The ADC takes an analog signal and changes into a series of binary numbers. The ADC may be used in simple digital display devices e. g. thermometers, light meters but it may also be used in digital sound recording and in data acquisition. However, a digital-to-analog converter(DAC) is used to change a digital signal to an analog signal. A DAC takes a series of binary numbers and converts it to an analog signal. It is common to find a DAC in the gain-control system of an op-amp which in turn may be used to control digital amplifiers and filters.[9]

Design difficulty

Digital systems require less skill and therefore are much easier to design than comparable analogue circuits. This is one of the main reasons why digital systems are more common than analog. An analogue circuit must be designed by hand, and the process is much less automated than for digital systems. In spite of its advantage in design and economics, once a digital electronic device has to interface with the real world, it needs an analog electronic device although the analog design process requires more experimentation. [10]

See also

External links


  1. ^ Concise Oxford dictionary (10 ed.). Oxford University Press Inc.. 1999. ISBN 0198602871.  
  2. ^ Plympton, George Washington (1884). The aneroid barometer: its construction and use. D. Van Nostran Co..  
  3. ^ Singmin, Andrew (2001). Beginning digital electronics through projects. Newnes. p. 9. ISBN 0750672696. "Signals come from transducers..."  
  4. ^ Miller, Mark R. (2002). Electronics the Easy Way. Barron's Educational Series. pp. 232-239. ISBN 0764119811. "Until the radio came along..."  
  5. ^ Hsu, Hwei Piao (2003). Schaum's outline of theory and problems of analog and digital communications. McGraw-Hill Professional. p. 202. ISBN 0071402286. "The presence of noise degrades the performance of communication systems."  
  6. ^ Carr, Joseph J. (2000). Secrets of RF circuit design. McGraw-Hill Professional. p. 423. ISBN 0071370677. "It is common in microwave systems..."  
  7. ^ Roe, David B.; Wilpon, Jay G. (1994). Voice communication between humans and machines. U.S. National Academy of Science Press. p. 19. ISBN 0309049887. "...microelectronics technology."  
  8. ^ Chen, Wai-Kai (2005). The electrical engineering handbook. Academic Press. p. 101. ISBN 0121709600. "Noise from an analog (or small-signal) perspective..."  
  9. ^ Scherz, Paul (2006). Practical electronics for inventors. McGraw-Hill Professional. p. 730. ISBN 0071452816. "In order for analog devices... to communicate with digital circuits..."  
  10. ^ Williams, Jim (1991). Analog circuit design. Newnes. p. 238. ISBN 0750696401. "Even within companies producing both analog and digital products..."  

Study guide

Up to date as of January 14, 2010

From Wikiversity

Analog electronics

Analog electronics is the study of electronic circuits which manipulate analog signals. This branch of electronics not only applies to devices purely in itself for analog signal processing, but also serves a vital, complementary role to digital electronic systems, in the field of mixed signal circuits. See the difference between analog and digital circuits w:Analog_circuits#Analogue_vs._digital_electronics

Analog systems deal with electrical quantities (of voltage and current) which vary continuously over a range. In this approach, they are fundamentally different from digital systems, which have to group ranges of these quantities together to be understood.


Sciences humaines.svg Educational level: this is a tertiary (university) resource.
Crystal Clear Sharemanager.png Resource type: this resource is a course.
Nuvola apps kcmsystem.svg Subject classification: this is an engineering resource .
Apollo 15 launch.jpg Completion status: this resource is just getting off the ground. Please feel welcome to help!

Got something to say? Make a comment.
Your name
Your email address