Bar (unit): Wikis


Note: Many of our articles have direct quotes from sources you can cite, within the Wikipedia article! This article doesn't yet, but we're working on it! See more info or our list of citable articles.

Did you know ...

More interesting facts on Bar (unit)

Include this on your site/blog:


From Wikipedia, the free encyclopedia

The bar (symbol bar) is a unit of pressure equal to 100 kilopascals, and roughly equal to the atmospheric pressure on Earth at sea level. Other units derived from the bar are the decibar (symbol dbar), centibar (symbol cbar), and millibar (symbol mbar or mb). They are not SI units, nor are they cgs units, but they are accepted for use with the SI by NIST.[1] The bar is widely used in descriptions of pressure because it is only about 1% smaller than "standard" atmospheric pressure, and is legally recognized in countries of the European Union.[2]

Except for the power of ten, the definition of bar fits in the sequence of SI pressure units (Pa, kPa, MPa), namely, 1 bar ≡ 100,000 Pa = 100 kPa = 0.1 MPa. This is in contrast to the well-known unit of pressure, atmosphere, which now is defined to be 1.01325 bar exactly. As a rule of thumb, a bar is almost equal to an atmosphere.

The bar and the millibar were introduced by the British meteorologist William Napier Shaw in 1909. William Napier Shaw was the director of the Meteorological Office in London from 1907 to 1920.[3]



The bar, decibar, centibar, and millibar are defined as:

  • 1 bar = 100 kPa (kilopascals) = 1,000,000 dynes per square centimeter (baryes) = 0.987 atm (atmospheres) = 14.5038 psi
  • 1 dbar = 0.1 bar = 10 kPa = 100,000 dyn/cm2
  • 1 cbar = 0.01 bar = 1 kPa
  • 1 mbar = 0.001 bar = 0.1 kPa = 1 hPa (hectopascal) = 1,000 dyn/cm2

Example conversion: 1 atm pressure = 1.01325 bar = 1.01325 x 105 Pa = 1.01325 x 105 N/m2


The word bar has its origin in the Greek word βάρος (baros), meaning weight. Its official symbol is "bar"; the earlier "b" is now deprecated, but still often seen especially in "mb" rather than the proper "mbar" for millibars.

The bar and millibar were introduced by Sir Napier Shaw in 1909 and internationally adopted in 1929.


Atmospheric air pressure is often given in millibars where "standard" sea level pressure is defined as 1013.25 mbar (hPa), equal to 1.01325 bar. Despite millibars not being an SI unit, meteorologists and weather reporters worldwide have long measured air pressure in millibars. After the advent of SI units, some meteorologists began using hectopascals (symbol hPa) which are numerically equivalent to millibars. For example, the weather office of Environment Canada uses kilopascals and hectopascals on their weather maps.[4][5] In contrast, Americans are familiar with the use of the millibar in US reports of hurricanes and other cyclonic storms.

Atmospheric air pressure is often expressed in millibars and sea level atmospheric air pressure is defined as 1013.25 mbar which is equivalent to 1 atm.

In water, there is an approximate numerical equivalence between the change in pressure in decibars and the change in depth from the sea surface in metres. Specifically, an increase of 1 decibar occurs for every 1.019716 metre increase in depth close to the surface. As a result, decibars are commonly used in oceanography.

Many engineers worldwide use the bar as a unit of pressure because, in much of their work, using pascals would involve using very large numbers.

In the automotive field, turbocharger boost is often described in the United Kingdom in terms of the bar.

Unicode has a character for "mb": (), but it exists only for compatibility with legacy Asian encodings. There is also a character "bar": .

Absolute pressure and gauge pressure

Bourdon tube pressure gauges, vehicle tire gauges, and many other types of pressure gauges are zero referenced to atmospheric pressure, which means that they measure the pressure above atmospheric pressure (which is around 1 bar); this is gauge pressure and is often referred to as barg (spoken "bar gauge"). In contrast, absolute pressures are zero referenced to a complete vacuum and when expressed in bar are often referred to as bara. Thus, the absolute pressure of any system is the gauge pressure of the system plus atmospheric pressure. The usage of bara and barg is now deprecated, with qualification of the physical property being preferred, e.g., "The gauge pressure is 2.3 bar; the absolute pressure is 3.3 bar".[2]

In the United States, where pressures are still often expressed in pounds per square inch (symbol psi), gauge pressures are referred to as psig and absolute pressures are referred to as psia. Gauge pressure is also sometimes spelled as gage pressure.

Sometimes, the context in which the word pressure is used helps to identify it as meaning either the absolute or gauge pressure. However, in truth, whenever a pressure is expressed in any units (bar, Pa, psi, atm, etc.), it should be denoted in some manner as being either absolute or gauge pressure to avoid any possible misunderstanding. One recommended way of doing so is to spell out what is meant, for example as bar gauge or kPa absolute.[6]

Other units of pressure

Pressure Units

technical atmosphere


pound-force per
square inch

1 Pa ≡ 1 N/m2 10−5 1.0197×10−5 9.8692×10−6 7.5006×10−3 145.04×10−6
1 bar 100,000 ≡ 106 dyn/cm2 1.0197 0.98692 750.06 14.5037744
1 at 98,066.5 0.980665 ≡ 1 kgf/cm2 0.96784 735.56 14.223
1 atm 101,325 1.01325 1.0332 ≡ 1 atm 760 14.696
1 torr 133.322 1.3332×10−3 1.3595×10−3 1.3158×10−3 ≡ 1 Torr; ≈ 1 mmHg 19.337×10−3
1 psi 6.894×103 68.948×10−3 70.307×10−3 68.046×10−3 51.715 ≡ 1 lbf/in2

Example reading:  1 Pa = 1 N/m2  = 10−5 bar  = 10.197×10−6 at  = 9.8692×10−6 atm, etc.

See also


This article incorporates material from the Citizendium article "Bar (unit)", which is licensed under the Creative Commons Attribution/Share-Alike 3.0 Unported License but not under the GFDL.


  1. ^ Units Outside of the SI, Table 7 (from the NIST website)
  2. ^ a b British Standard BS 350:2004 Conversion Factors for Units
  3. ^ Sir William Napier Shaw
  4. ^ Environment Canada Weather Map
  5. ^ Weather - Environment Canada
  6. ^ FAQ (from the website of the National Physics Laboratory, United Kingdom)

External links

Simple English

The bar (symbol bar), decibar (symbol dbar) and the millibar (symbol mbar, also mb) are units of pressure. They are not SI units, but they are anyhow also used with (although discouraged) for use with the SI. The bar is still used in descriptions of pressure because it is about the same as atmospheric pressure.


The bar, decibar and millibar are known as:

  • 1 bar = 100,000 pascals (Pa) = 1,000,000 dynes per square centimeter (baryes)
  • 1 dbar = 0.1 bar = 10,000 Pa = 100,000 dyn/cm²
  • 1 mbar = 0.001 bar = 100 Pa = 1,000 dyn/cm²

(A pascal is one newton per square meter.)


The word bar has its origin in the Greek word βάρος (baros), meaning weight. Its official symbol is "bar"; the earlier "b" is now no longer used, but still often seen especially as "mb" rather than the correct "mbar" for millibars.

The bar and millibar were defined by Sir Napier Shaw in 1909 and internationally used in 1929.

Other websites

Got something to say? Make a comment.
Your name
Your email address