|Blohm & Voss BV 155|
|Blohm & Voss BV 155|
|Manufacturer||Blohm & Voss|
|First flight||1 September 1944|
The Blohm & Voss BV 155 was a German high-altitude interceptor aircraft intended to be used by the Luftwaffe against raids by USAAF B-29 Superfortresses. Work started on the design in 1942, but the design went through a protracted development period and was still under construction when World War II ended.
The saga of the BV 155 began at Messerschmitt in the spring of 1942. At that time, it was known under the designation of Me 155, and was a company proposal for a carrier-based single-seat fighter. The Me 155 was intended to be based aboard the aircraft carrier Graf Zeppelin, then under construction. In the interest of economy and simplicity, the Me 155 was to use as many Messerschmitt Bf 109 components as possible, being basically a navalized version of the earlier Messerschmitt fighter.
The Me 155 was to be powered by a DB 605A-1 liquid-cooled engine of 1,475 PS (1,455 hp, 1,085 kW). The fuselage was more-or-less that of the standard Bf 109G, but with an entirely new wing. The undercarriage retracted inwards into wing wells, providing the wider track required for safe carrier landings. Standard naval equipment such as folding wings, catapult spools, and arrester gear were to be fitted. Proposed armament was an engine mounted 20 mm MG 151 cannon and two 20 mm MG 151 cannons and two 13 mm (.51 in) MG 131 machine guns in wings. It had an estimated maximum speed of 649 km/h (403 mph).
Detail design of the Me 155 was complete by Sept 1942. However, the numerous delays in the Graf Zeppelin seemed to indicate that the completion of the carrier would be at least two years away. Messerschmitt was told to shelve the Me 155 project for the indefinite future. Work on the Graf Zeppelin carrier was eventually abandoned.
In order that all of that work on the Me 155 project not go entirely to waste, Messerschmitt adapted its design in November 1942 to match a Luftwaffe requirement for a fast single seat bomber. A single 1,000 kg (2,210 lb) SC 1000 bomb was to be carried. All of the carrier equipment and most of the armament was removed from the aircraft. Additional fuel tanks were provided and an elongated, non-retractable tailwheel was added to provide ground clearance for the large bomb. The proposal was designated Me 155A.
By the end of 1942, the increasing number of USAAF bombing raids and intelligence coming in about the new American B-29 bomber led the Luftwaffe to envisage a pressing need for an effective high-altitude interceptor. Messerschmitt adapted its design to this requirement under the designation Me 155B. The engine was to be the DB 628, which was basically a DB 605A with a two-stage mechanical supercharger with an induction cooler. A pressurized cabin was to be provided. It was estimated that a service ceiling of 14,097 m (46,250 ft) could be attained.
A converted Bf 109G adapted to take the DB 628 engine flew in May 1942 and attained an altitude of 15,500 m (50,850 ft). However, the Technische Amt concluded that a DB 603A engine with an exhaust-driven turbosupercharger was more promising. The DB 603A provided 1,201 kW (1,610 hp) for takeoff and 1,081 kW (1,450 hp) at 15,000 m (49,210 ft). This engine change required that the fuselage be elongated in order to house the turbosupercharger aft of the pressure cabin. Exhaust gases were carried to the turbosupercharger via external ducts. Air was drawn in through via a ventral trough aft of the wing. Standard Bf 109G wings were to be fitted outboard of a new, long-span, untapered wing center section. Other parts were scavenged from existing Messerschmitt designs – the vertical tail was from the Me 209, and the horizontal tail and the undercarriage were taken from the Bf 109G.
In August 1943, the Technische Amt decided that Messerschmitt was over-committed, and they decided to transfer the work on the design to Blohm & Voss. After some initial study, the Blohm & Voss design team deemed that the existing Messerschmitt design had too many weaknesses. Several months of argument and finger-pointing between the Messerschmitt transition team and the Blohm & Voss designers followed. Friction between the two teams got steadily worse. In the event, no meeting of the minds was possible, and the Technische Amt eventually decided to throw Messerschmitt off the project entirely, and turn it entirely over to Blohm & Voss.
In September 1943, an order for five prototypes was placed. Blohm & Voss decided that the design problems still needed fixing, but by late 1943 they still hadn't been addressed. A meeting was called to finally address these problems, but the Messerschmitt people didn't bother to show up. As late as November 1943 changes were still being made, and Blohm & Voss decided to remove the complex underwing radiators favoured by Messerschmitt for two large scoop-type units mounted above the wings. B&V built a mock-up and had it tested in the LFA wind tunnel, but Messerschmitt refused to help. Late in 1943, Blohm & Voss formally advised the RLM of their problems with Messerschmitt and implored them to intervene. By this point, the T-Amt was just as fed up, and removed Messerschmitt from the project entirely.
The design, now named the BV 155A, was finally completely in the hands of one design team. B&V modified the design with a completely new laminar flow wing in place of the original "extended" one from the Me 155. They also changed details of many other parts of the plane, including new landing gear (from the Ju 87) and a new tail unit. Further wind tunnel testing showed that there was a serious problem with the overwing radiators, at high angles of attack the wing "blanked" them from the airflow and cooling would suffer. The decision was made to abandon the A model completely and move on.
The Blohm & Voss team elected to adopt a laminar-flow airfoil section, and abandoned the idea of using standard Bf 109G wings for the outer panels. The wing center section was redesigned. Two large radiators were mounted over the wing trailing edges at the extremities of the center section. Ju 87D-6 undercarriage legs and wheels used instead of the Bf 109G units. The Bf 109G horizontal tail surfaces were replaced with larger area freshly-designed units, and the vertical tail surface was increased in size.
The first prototype was designated BV 155 V1, and flew for the first time on September 1, 1944. Tests with the V1 showed that the outboard radiators were not sufficiently effective in providing cooling, especially at high angles of attack. The intakes on the next prototype were enlarged and underslung beneath the wing rather than placed over it. However, the enlarged radiators caused a CoG problem, which required moving the pressurized cockpit forward. The Blohm & Voss team took this opportunity to replace the original Bf 109G canopy with an aft-sliding all-round vision canopy, and the rear fuselage decking was cut down. This in turn required that a larger rudder be fitted. The ventral radiator bath was also enlarged.
All these changes were incorporated into the BV 155 V2, which flew for the first time on February 8, 1945. which was the first genuine B series aircraft. The Blohm & Voss team was still not satisfied with the design, and before the V2 began its flight trials they proposed that the engine be switched to the DB 603U having the larger mechanically-driven supercharger of the DB 603E. The DB 603U promised a power of 1,238 kW (1,660 hp) for takeoff and 1,066 kW (1,430 hp) at 14,935 m (49,000 ft). The ventral turbosupercharger was retained. The Technische Amt decided to accept this proposal, and abandoned all work on the BV 155B in favor of the revised design, which was designated BV 155C.
While all of this was going on, Blohm & Voss designers had been working on additional changes under Projekt 205. P.205 replaced the underwing radiators with an annular one around the front of the engine, a design feature commonly found on a number of German designs. With the wings now free of clutter, they were considerably simpler and were reduced in span. This also had the side effect of reducing the track, which would later prove to be a welcome change. The new design would be simpler, lighter and faster, and plans were made to make it the standard version of the aircraft. During the October re-evaluation, it was agreed that V1 through V3 would be completed as B models, while a new series of five would be completed to the new standard as the BV 155C.
The BV 155C was quite different in appearance from the BV 155B. The clumsy wing-mounted radiators of the BV 155B were eliminated, and the main landing gear leg attachment points were moved inboard to retract inwards. The cooling was provided by an annular frontal radiator à la Ta 152. Large circular intakes were attached to the fuselage sides above the wing roots.
In the meantime, the BV 155 V2 was damaged beyond repair during a bad landing. It was to be replaced in the test program by the BV 155V3. The BV 155V3 differed from the V2 in having the DB 603U intended for the BV 155C. However, the engine cowling and turbosupercharger were unchanged.
Various armament schemes for the BV 155B were proposed. One proposal had an engine-mounted (or Motorkanone) 30 mm (1.18 in) MK 108 cannon and two 20 mm MG 151/20 cannons. Another had a Motorkanone-mount 30 mm (1.18 in) MK 103 cannon and two wing-mounted 20 mm MG 151 cannons. Estimated maximum speed was 650 km/h (400 mph) at 12,000 m (39,370 ft) and 690 km/h (430 mph) at 15,999 m (52,490 ft). Service ceiling was to be 16,950 m (55,610 ft). Empty weight was 4,869 kg (10,734 lb). Normal loaded weight ranged from 5,126-5,488 kg (11,300-12,100 lb), depending on the armament provided.
On May 3, 1945, the city of Hamburg surrendered to the British Army, who ordered everyone out of the Blohm & Voss plant. BV 155 V1 was found in a flyable state, and the British brought in a pilot to fly it to the UK for testing. Unfortunately, the aircraft encountered problems immediately and crash-landed. All the parts for the still-incomplete V2 and V3 were shipped to Royal Aircraft Establishment at Farnborough, and V2 was put on public display in October. There was some discussion of completing the aircraft using parts of V3, but it was believed this did not take place, and one of the aircraft was later handed over to the U.S. The aircraft was evaluated at Wright Field near Dayton, Ohio, and was given the foreign equipment number FE-505. This aircraft was eventually transferred to the National Air and Space Museum's storage facility in Suitland, Maryland. For years it was believed that this aircraft was the incomplete V3 aircraft, and that the British had retained V2 for their own display, though no record of the aircraft's fate could be found. In 1998 restoration efforts by two of the NASM staff revealed that the sole surviving aircraft is in fact V2, with some of V3's parts applied to the airframe. It is now believed that the British attempted to restore V2 by combining both aircraft prior to donating it to the U.S. This also explains why no record of V3 exists after the U.S. received the aircraft.
Related lists List of military
aircraft of Germany