Lumber: Wikis

  
  
  

Note: Many of our articles have direct quotes from sources you can cite, within the Wikipedia article! This article doesn't yet, but we're working on it! See more info or our list of citable articles.

Did you know ...


More interesting facts on Lumber

Include this on your site/blog:

Encyclopedia

From Wikipedia, the free encyclopedia

Timber in storage for later processing at a sawmill
Wood cut from Victorian Eucalyptus regnans

Lumber or timber is wood that is used in any of its stages from felling through readiness for use as structural material for construction, or wood pulp for paper production. (The distinction between the two terms is discussed below.)

Lumber is supplied either rough or finished. Besides pulpwood, rough lumber is the raw material for furniture-making and other items requiring additional cutting and shaping. It is available in many species, usually hardwoods. Finished lumber is supplied in standard sizes, mostly for the construction industry, primarily softwood from coniferous species including pine, fir and spruce (collectively known as Spruce-pine-fir), cedar, hemlock, but also some hardwood, for high-grade flooring.

Contents

Terminology

In the United Kingdom and Australia, "timber" is a term also used for sawn wood products (that is, boards), whereas generally in the United States and Canada, the product of timber cut into boards is referred to as lumber. In the United States and Canada, timber often refers to the wood contents of standing, live trees that can be used for lumber or fibre production, although it can also be used to describe sawn lumber whose smallest dimension is not less than 5 inches (127 mm).[1]

Note that the word lumberjack is used in the UK and Australia to refer to North Americans who fell standing trees, and so the word "lumber" conjures images of what North Americans call "timber", and vice versa.

"Timber!" is also an interjection that lumberjacks often shout out to warn others that a cut tree is about to fall.

Dimensional lumber

Example of 2×4.

Dimensional lumber is a term used for lumber that is finished/planed and cut to standardized width and depth specified in inches. Examples of common sizes are 2×4 (pictured, also two-by-four and other variants, such as four-by-two in the UK, Australia, New Zealand), 2×6, and 4×4. The length of a board is usually specified separately from the width and depth. It is thus possible to find 2×4s that are four, eight, or twelve feet in length. In the United States the standard lengths of lumber are 6, 8, 10, 12, 14, 16, 18, 20, 22, and 24 feet.

North American softwood dimensional lumber sizes
Nominal Actual Nominal Actual Nominal Actual
1 × 2 34 in × 1+12 in (19 mm × 38 mm) 2 × 2 1+12 in × 1+12 in (38 mm × 38 mm) 4 × 4 3+12 in × 3+12 in (89 mm × 89 mm)
1 × 3 34 in × 2+12 in (19 mm × 64 mm) 2 × 3 1+12 in × 2+12 in (38 mm × 64 mm) 4 × 6 3+12 in × 5+12 in (89 mm × 140 mm)
1 × 4 34 in × 3+12 in (19 mm × 89 mm) 2 × 4 1+12 in × 3+12 in (38 mm × 89 mm) 6 × 6 5+12 in × 5+12 in (140 mm × 140 mm)
1 × 6 34 in × 5+12 in (19 mm × 140 mm) 2 × 6 1+12 in × 5+12 in (38 mm × 140 mm) 8 × 8 7+14 in × 7+14 in (184 mm × 184 mm)
1 × 8 34 in × 7+14 in (19 mm × 184 mm) 2 × 8 1+12 in × 7+14 in (38 mm × 184 mm)
1 × 10 34 in × 9+14 in (19 mm × 235 mm) 2 × 10 1+12 in × 9+14 in (38 mm × 235 mm)
1 × 12 34 in × 11+14 in (19 mm × 286 mm) 2 × 12 1+12 in × 11+14 in (38 mm × 286 mm)

Note: Treated 8x8 SYP pilings are actually 8" x 8"

Solid dimensional lumber typically is only available up to lengths of 24 ft, yet since builders have a need for lengths beyond that for roof construction (rafters), builders use "finger-jointed" lumber that can be up to 36 ft long in 2×6 size (see Engineered Lumber below). Finger-jointed lumber is also widely used for smaller lengths like studs, the vertical members of a framed wall. Pre-cut studs save a framer a lot of time as they are pre-cut by the manufacturer to be used in 8 ft, 9 ft & 10 ft ceiling applications, which means they have removed a few inches of the piece to allow for the sill plate and the double top plate with no additional sizing necessary by the framer.

In the Americas, two-bys (2×4s, 2×6s, 2×8s, 2×10s, and 2×12s), along with the 4×4, are common lumber sizes used in modern construction. They are the basic building block for such common structures as balloon-frame or platform-frame housing. Dimensional lumber made from softwood is typically used for construction, while hardwood boards are more commonly used for making cabinets or furniture.

For convenience, we refer to lumber by its nominal dimensions, which are larger than the actual dimensions (see above table). Nominal dimensions traditionally referred to rough lumber, but the size is reduced in drying and planing. Early standards called for rough lumber to be of full nominal dimension, often in the dry condition, but the requirements have decreased through time—the typical 13/16 inches for a finished 1-inch board in the 1910s was reduced by 4% in 1929 and by another 4% in 1956, resulting in the current standard of 3/4 inch.[2]

The move to set national standards for lumber in the United States began with publication of the American Lumber Standard in 1924, which set specifications for lumber dimensions, grade, and moisture content; it also developed inspection and accreditation programs. These standards have changed over the years to meet the changing needs of manufacturers and distributors, so that lumber would remain competitive with alternative construction products. Current standards are set by the American Lumber Standard Committee, appointed by the Secretary of Commerce.[3]

Attempts to maintain lumber quality over time have been challenged by historical changes in the timber resources of the United States—from the slow-growing virgin forests common over a century ago to the fast-growing plantations now common in today's commercial forests. Resulting declines in lumber quality have shifted use to alternative construction products and have been of recent concern to both the lumber industry and consumers.[4][5]

Hardwoods

Hardwood dimensional lumber sizes
Nominal Surfaced 1 Side (S1S) Surfaced 2 sides (S2S)
12 in 38 in 516 in
58 in 12 in 716 in
34 in 58 in 916 in
1 in or 44 in 78 in 1316 in
1+14 in or 54 in 1+18 in 1+116 in
1+12 in or 64 in 1+38 in 1+516 in
2 in or 84 in 1+1316 in 1+34 in
3 in or 124 in 2+1316 in 2+34 in
4 in or 164 in 3+1326 in 3+34 in

In North America sizes for dimensional lumber made from hardwoods varies from the sizes for softwoods. Boards are usually supplied in random widths and lengths of a specified thickness, and sold by the board-foot (144 cubic inches, 112th of a cubic foot). This does not apply in all countries, for example in Australia many boards are sold to timber yards in packs with a common profile (dimensions) but not necessarily of consisting of the same length boards. Hardwoods cut for furniture are cut in the fall and winter, after the sap has stopped running in the trees. If hardwoods are cut in the spring or summer the sap ruins the natural color of the timber and deteriorates the value of the timber for furniture.

Also in North America hardwood lumber is commonly sold in a “quarter” system when referring to thickness. 4/4 (four quarters) refers to a one-inch thick board, 8/4 (eight quarters) is a two-inch thick board, etc. This system is not usually used for softwood lumber, although softwood decking is sometimes sold as 5/4 (actually one inch thick).

Engineered lumber

Engineered lumber is lumber created by a manufacturer and designed for a certain structural purpose. The main categories of engineered lumber are:[6]

  1. Laminated Veneer Lumber (LVL) – LVL comes in 1+34 inch thicknesses with depths such as 9+12, 11+78, 14, 16, 18, or 24 inches, and are often doubled or tripled up. They function as beams to provide support over large spans, such as removed support walls and garage door openings, places where dimensional lumber isn't sufficient, and also in areas where a heavy load is bearing from a floor, wall or roof above on a somewhat short span where dimensional lumber isn't practical. This type of lumber cannot be altered by holes or notches anywhere within the span or at the ends, as it compromises the integrity of the beam, but nails can be driven into it wherever necessary to anchor the beam or to add hangers for I-joists or dimensional lumber joists that terminate at an LVL beam.
  2. Wood I-joists – Sometimes called "TJI","Trus Joists" or "BCI", all of which are brands of wood I-joists, they are used for floor joists on upper floors and also in first floor conventional foundation construction on piers as opposed to slab floor construction. They are engineered for long spans and are doubled up in places where a wall will be aligned over them, and sometimes tripled where heavy roof-loaded support walls are placed above them. They consist of a top and bottom chord/flange made from dimensional lumber with a webbing in-between made from oriented strand board (OSB). The webbing can be removed up to certain sizes/shapes according to the manufacturer's or engineer's specifications, but for small holes, wood I-joists come with "knockouts", which are perforated, pre-cut areas where holes can be made easily, typically without engineering approval. When large holes are needed, they can typically be made in the webbing only and only in the center third of the span; the top and bottom chords cannot be cut. Sizes and shapes of the hole, and typically the placing of a hole itself, must be approved by an engineer prior to the cutting of the hole and in many areas, a sheet showing the calculations made by the engineer must be provided to the building inspection authorities before the hole will be approved. Some I-joists are made with W-style webbing like a truss to eliminate cutting and allow ductwork to pass through.
    Freshly cut logs showing sap running from beneath bark
  3. Finger-Jointed Lumber – Solid dimensional lumber lengths typically are limited to lengths of 22 to 24 feet, but can be made longer by the technique of "finger-jointing" lumber by using small solid pieces, usually 18 to 24 inches long, and joining them together using finger joints and glue to produce lengths that can be up to 36 feet long in 2×6 size. Finger-jointing also is predominant in precut wall studs. It is also an affordable alternative for non-structural hardwood that will be painted (staining would leave the finger-joints visible).
  4. Glu-lam Beams – Created from 2×4 or 2×6 stock by gluing the faces together to create beams such as 4×12 or 6×16. By gluing multiple, common sized pieces of lumber together, they act as one larger piece of lumber - thus eliminating the need to harvest larger, older trees for the same size beam.
  5. Manufactured Trusses – Trusses are used in home construction as a pre-fabricated replacement for roof rafters and ceiling joists (stick-framing). It is seen as an easier installation and a better solution for supporting roofs as opposed to the use of dimensional lumber's struts and purlins as bracing. In the southern USA and other parts, stick-framing with dimensional lumber roof support is still predominant. The main drawback of trusses are reduced attic space, time required for engineering and ordering, and a cost higher than the dimensional lumber needed if the same project were conventionally framed. The advantages are significantly reduced labor costs (installation is faster than conventional framing), consistency, and overall schedule savings.

Defects in lumber

Defects occurring in Timber are grouped into the following five divisions:

Defects due to conversion

During the process of converting timber to commercial form, the following defects may occur:

  1. Chip mark
  2. Diagonal grain
  3. Torn grain
  4. Wane

Defects due to fungi

Fungi attacks timber when these conditions are all present:

  1. The timber moisture content is above 20%
  2. The environment is warm enough
  3. There is air

Wood with less than 20% moisture remains free of fungi for centuries. Similarly, wood submerged in water will not be attacked by fungi because of absence of air.

Fungi timber defects:

  1. Blue stain
  2. Brown rot
  3. Dry rot
  4. Heart rot
  5. Sap stain
  6. Wet rot
  7. White rot

Defects due to insects

Following are the insects which are usually responsible for the decay of timber:

  1. Beetles
  2. Marine Borers
  3. Termites
  4. Red Ant

Defects due to natural forces

There are two main natural forces responsible for causing defects in timber: abnormal growth and rupture of tissues.

Defects due to seasoning

Defects due to seasoning are the number one cause for splinters and slivers.

Preservatives

Fasteners used with treated lumber require special consideration because of the corrosive chemicals used in the treatment process.

Timber or lumber may be treated with a preservative that protects it from being destroyed by insects, fungus or exposure to moisture. Generally this is applied through combined vacuum and pressure treatment. The preservatives used to pressure-treat lumber are classified as pesticides. Due to potential hazards to humans and the environment, some are being phased out. Many newer preservatives are free of metallic compounds altogether, and are instead based on biodegradable organic chemistry. Treating lumber provides long-term resistance to organisms that cause deterioration. If it is applied correctly, it extends the productive life of lumber by five to ten times. If left untreated, wood that is exposed to moisture or soil for sustained periods of time will become weakened by various types of fungi, bacteria or insects.

Timber framing

Timber framing is a style of construction which uses heavier framing elements than modern stick framing, which uses dimensional lumber. The timbers originally were tree boles squared with a broadaxe or adze and joined together with joinery without nails. A modern imitation with sawn timbers is growing in popularity in the United States.

One of the most conventional framing methods is the Neumann Notch, which involves a thirty-two degree angling of adjoining lumber and then a right-angled wedge with an eighteen degree cusp fitted between the lumber before being bolted. This convention was pioneered by Daniel R. Neumann, a carpenter from Germany, that was responsible for the structural development of the Massachusetts Bay Colony in 1630. This framing convention spread to construction sites in other colonies, most famously Plymouth and Concord. Neumann's notched framing then was adopted by carpenters and construction companies and this framing convention is still used today in traditional frame sets.

Another somewhat less conventional method for framing is known as the "New-style" binding. The basic setup of the New-style binding was developed by Austin D. New, a Mormon settler in Salt Lake City, Utah during the 1800s. The basic structure of the New-style binding involves a set-up of two similar sized logs set against each other perpendicularly and lashed together with hemp rope. This technique was used to construct many of the early houses of the Mormon settlers due to its ease of use and durability. Eventually the New-style binding became obsolete as the settlers began constructing homes out of the more traditional brick and mortar.

Residual Wood

The conversion from coal to biomass power is a growing trend in the United States [7].

A coal-fired power plant in Pepeekeo, Hawaii that formerly provided electricity to a sugar mill is now being converted into a 24-megawatt (MW) biomass power plant. MMA Renewable Ventures [8] is financing the conversion and will operate the new plant, which will be called the Hū Honua Bioenergy Facility [9]. Located about 8 miles north of Hilo on the Big Island of Hawaii, the facility will draw on residual wood from the local timber industry and other biomass wastes to produce enough power for about 18,000 homes, meeting up to 10% of the Big Island's electricity needs.

Remanufactured Lumber

Remanufactured Lumber refers to secondary or tertiary processing/cutting of previously milled lumber. The term specifically refers to lumber cut for industrial or wood packaging use. Lumber is cut by ripsaw or resaw to create dimensions that are not usually processed by a primary sawmill.

Resawing is the process of splitting 1 inch through 12 inch hardwood or softwood lumber into two or more thinner pieces of full length boards. For example, splitting a ten foot 2x4 into two ten foot 1x4s is considered resawing.

In addition to resawing lumber, remanufactured lumber can be ripped on a ripsaw using single or multiple blades. Ripping is the process of splitting 1" through 12" hardwood or softwood lumber into two or more narrower pieces of full length boards. For example, splitting a ten foot 2x4 into two ten foot 2x2s is considered ripping.[10]

See also

References

External links


1911 encyclopedia

Up to date as of January 14, 2010

From LoveToKnow 1911

LUMBER, a word now meaning (1) useless discarded furniture or other rubbish, particularly if of a bulky or heavy character; (2) timber, when roughly sawn or cut into logs or beams (see TIMBER); (3) as a verb, to make a loud rumbling noise, to move in a clumsy heavy way, also to burden with useless material, to encumber. "Lumber" and "lumber-house" were formerly used for a pawnbroker's shop, being in this sense a variant of "Lombard," a name familiar throughout Europe for a banker, money-changer or pawnbroker. This has frequently been taken to be the origin of the word in sense (I), the reference being to the store of unredeemed and unsaleable articles accumulating in pawnbrokers' shops. Skeat adopts this in preference to the connexion with "lumber" in sense (3), but thinks that the word may have been influenced by both sources (Etym. Diet., 1910). This word is probably of Scandinavian origin, and is cognate with a Swedish dialect word lomra, me thing "to roar," a frequentative of ljumma, " to make a noise." The English word may be of native origin and merely onomatopoeic. The New English Dictionary, though admitting the probability of the association with "Lombard," prefers the second proposed derivation. The application of the word to timber is of American origin; the New English Dictionary quotes from Suffolk (Mass.) Deeds of 1662 - "Freighted in Boston, with beames ... boards. .. and other lumber."


<< Lumbago

Lumbini >>


Simple English

Lumber or Timber is a term used to describe wood from the time trees are felled, to its end product as a material suitable for industrial use—as structural material for construction or wood pulp for paper production.

In the U.K. and Australia, "timber" is a term also used for sawn wood products (that is, boards), whereas generally in the United States and Canada, the product of timber cut into boards is referred to as lumber. In the United States and Canada sawn wood products of five inches diameter or greater (4½″ nominal size) are sometimes called "timbers".


Lumber is supplied either rough or finished. Rough lumber is the raw material for furniture making. It is available in many species, usually hardwoods.

Contents

Dimensional Lumber

Dimensional lumber is a term used in North America for lumber that is finished/planed and cut to standardized width and depth specified in inches.

Softwoods

Softwood Dimensional Lumber Sizes
Nominal Actual Nominal Actual
1 × 2 ¾″ × 1½″ (19×38 mm) 2 × 2 1½″ × 1½″ (38×38 mm)
1 × 3 ¾″ × 2½″ (19×64 mm) 2 × 3 1½″ × 2½″ (38×64 mm)
1 × 4 ¾″ × 3½″ (19×89 mm) 2 × 4 1½″ × 3½″ (38×89 mm)
1 × 6 ¾″ × 5½″ (19×140 mm) 2 × 6 1½″ × 5½″ (38×140 mm)
1 × 8 ¾″ × 7¼″ (19×184 mm) 2 × 8 1½″ × 7¼″ (38×184 mm)
1 × 10 ¾″ × 9¼″ (19×235 mm) 2 × 10 1½″ × 9¼″ (38×235 mm)
1 × 12 ¾″ × 11¼″ (19×286 mm) 2 × 12 1½″ × 11¼″ (38×286 mm)
3 × 4 2½″ × 3½″ (64×89 mm) 2 × 14 1½″ × 13¼″ (38×337 mm)
4 × 4 3½″ × 3½″ (89×89 mm) 6 × 6 5½″ × 5½″ (140×140 mm)
4 × 6 3½″ × 5½″ (89×140 mm) 8 × 8 7¼″ × 7¼″ (184×184 mm)

Examples of common sizes are 2×4 (also two-by-four and other variants), 2×6, and 4×4. The length of a board is usually specified separately from the width and depth. It is thus possible to find 2×4s that are four, eight, or twelve feet in length. In the United States the standard lengths of lumber are 6, 8, 10, 12, 14, 16, 18, 20, 22, and 24 feet.

Non-North American sizes

Examples of Dimensional Lumber Sizes (Softwood and Hardwood)
Inch name Sawed Swedish Australian
2 × 4 50 x 100 mm 45 × 95 mm 45 x 90 mm
1 × 3 25 × 75 mm 22 × 70 mm 19 x 70 mm
3 × 3 75 × 75 mm 70 × 70 mm 70 x 70 mm
2 × 7 50 × 175 mm 45 × 170 mm Not used
2 × 3 50 × 75 mm 45 × 70 mm 45 x 70 mm
1 × 4 25 × 100 mm 22 × 95 mm 19 x 90 mm
1 × 5 25 × 125 mm 22 × 120 mm 19 x 120 mm
2 × 5 50 × 125 mm 45 × 120 mm 45 x 120 mm

Outside North America sizes of timber vary slightly. Sizes are, in some cases, based on the imperial measurement and referred to as such; in other cases the sizes are too far removed from the imperial size to be referred to by imperial measurement. Lengths are sold every 300 mm (a metric approximation of 1'). Common sizes are similar to the North American equivalent; 2.4, 2.7, 3.0, 3.6, 4.2, 4.8, 5.4, 6.0.

Hardwoods

Hardwood Dimensional Lumber Sizes
Nominal Surfaced 1 Side (S1S) Surfaced 2 sides (S2S)
⅜″ ¼″ 3/16″
½″ ⅜″ 5/16″
⅝″ ½″ 7/16″
¾″ ⅝″ 9/16″
1″ or 4/4 ⅞″ 13/16″
1¼″ or 5/4 1⅛″ 1-1/16″
1½″ or 6/4 1⅜″ 1-5/16″
2″ or 8/4 1-13/16″ 1¾″
3″ or 12/4 2-13/16″ 2¾″
4″ or 16/4 3-13/16″ 3¾″

In North America sizes for dimensional lumber made from hardwoods varies from the sizes for softwoods. Boards are usually supplied in random widths and lengths of a specified thickness, and sold by the board-foot (144 cubic inches).

Engineered Lumber

Engineered lumber is lumber created by a manufacturer and designed for a certain structural purpose.

Other pages

Other websites








Got something to say? Make a comment.
Your name
Your email address
Message