The Full Wiki

Revolver: Wikis

  
  
  
  

Note: Many of our articles have direct quotes from sources you can cite, within the Wikipedia article! This article doesn't yet, but we're working on it! See more info or our list of citable articles.

Did you know ...


More interesting facts on Revolver

Include this on your site/blog:























































Encyclopedia

From Wikipedia, the free encyclopedia

A seven-chambered Nagant M1895 with gate open for loading
Example of a swing out cylinder on a six-chambered revolver

A revolver is a repeating firearm that has a cylinder containing multiple chambers and at least one barrel for firing. As the user cocks the hammer, the cylinder revolves to align the next chamber and round with the hammer and barrel, which gives this type of firearm its name. In modern revolvers, the revolving cylinder typically chambers 5 or 6 rounds, but some models hold 10 rounds or more. Revolvers are most often handguns, but other weapons may also have the design of a revolver. These include some models of grenade launchers, shotguns, and some rifles.

Contents

Design

A revolver works by having several firing chambers arranged in a circle in a cylindrical block that are brought into alignment with the firing mechanism and barrel one at a time. In contrast, other repeating firearms, such as lever-action, pump-action, and semi-automatic, have a single firing chamber and a mechanism to load and extract cartridges into it.

A single action revolver requires the hammer to be pulled back by hand before each shot, which also revolves the cylinder. This leaves the trigger with just one "single action" left to perform - releasing the hammer to fire the shot - so the force and distance required to pull the trigger can be minimal. In contrast, with a self-cocking revolver, one long squeeze of the trigger pulls back the hammer and revolves the cylinder then finally fires the shot. They can generally be fired faster than a single action, but at the cost of reduced accuracy in the hands of most shooters.

Most modern revolvers are "traditional double action", which means they are able to operate either in single action or self-cocking mode. The accepted meaning of "double action" has, confusingly, come to be the same as "self-cocking", so modern revolvers that cannot be pre-cocked are called "double-action-only". These are intended for concealed carry, because the hammer of a traditional design is prone to snagging on clothes when drawn.

Most commonly, such guns have a 5- or 6-shot capacity, hence the common names of "six-gun" or "six-shooter". However, some revolvers have a 7- to 10-shot capacity, often depending on the caliber. Each chamber has to be reloaded manually, which makes reloading a revolver a much slower procedure than reloading a semi-automatic pistol.

The alternatives are a replaceable cylinder, a speedloader, which can reload all chambers at once, or a moon clip that holds a full load (or even half of one in the case of a half-moon clip) of ammunition and that is inserted along with the ammunition. Another product known as a "speedstrip" cannot reload a completely empty revolver as rapidly as a speedloader, but is less expensive, flatter, and more flexible when it comes to partial reloads.

Compared to autoloading handguns, a revolver is often simpler to operate (despite often being more mechanically complex) and may have greater reliability (depending on factors such as firmness of grip, ammunition or cartridge used, and degree of maintenance and lubrication provided to the firearm). For example, should a semiautomatic pistol fail to fire, clearing the chamber requires manually cycling the action to remove the errant round, as cycling the action normally depends on the energy of a cartridge firing. With a revolver, this is not necessary as none of the energy for cycling the revolver comes from the firing of the cartridge, but is supplied by the user either through cocking the hammer or, in a double action design, by just squeezing the trigger. Another significant advantage of revolvers is superior ergonomics, particularly for users with small hands. A revolver's grip is not required to accommodate a magazine, and it can be designed or customized much more than a typical semi-automatic.

In general, revolvers stand up to long-term neglect better than semi-automatics, an example of neglect being the common scenario of a civilian who keeps a weapon for defense but rarely shoots or maintains it. A revolver can be kept loaded and ready to fire without compressing any springs (which weaken over time with continual load)[citation needed] and is not very dependent on lubrication for proper firing. However, a revolver is generally not as resistant to abuse as a semi-automatic (abuse meaning dropping the weapon, or allowing severe contamination by dirt or mud). The revolver's clockwork-like internal parts are relatively delicate and can become misaligned after a severe impact, and its revolving cylinder can become jammed by excessive dirt or debris. The latter factors are more of a concern for military users than civilians or police.

Over the long period of development of the revolver, many calibers have been used. Some of these have proved more durable during periods of standardization and some have entered general public awareness. Among these are the .22 rimfire, a caliber popular for target shooting and teaching novice shooters; .38 Special and .357 Magnum, known for its police use; the .44 Magnum, famous from Clint Eastwood's "Dirty Harry" films; and the .45 Long Colt, used in the Colt revolver of the Wild West. Introduced in 2003, the Smith & Wesson Model 500 is the most powerful production revolver ever created, using the .500 S&W Magnum round.

The LeMat Revolver, an unusual revolver from the American Civil War era with 9 revolving chambers firing bullets and a center barrel firing shot.

As revolvers are of a 19th-century design, it is not surprising that semi-automatic pistols have largely overtaken them in military and law enforcement applications. Their lower ammunition capacities and relatively longer reload times compared to autoloading pistols are the main reasons for the switchover that occurred in the 1980s and 1990s. Additionally, the flat profile of semi-automatics make them more suitable for concealed carry. Revolvers still remain popular in the role of back-up (and off-duty) guns among American law enforcement officers and security guards. Also, revolvers are still common in the American private sector as defensive and sporting/hunting firearms. Famous police and military revolvers include the Webley, the Colt Single Action Army, the Smith & Wesson Model 29, the Smith & Wesson Model 10, and the Smith & Wesson 1917.

Revolver technology does live on in other weapons used by the military. Some autocannons and grenade launchers use mechanisms similar to revolvers, and some riot shotguns use spring loaded cylinders holding up to 12 rounds. In addition to serving as backup guns, revolvers still fill the specialized niche role as a shield gun; law enforcement personnel using a "bulletproof" ballistic shield (Gun shield) sometimes opt for a revolver instead of a self-loading pistol, because the slide of a pistol may strike the front of the shield when fired. Revolvers do not suffer from this disadvantage. A second revolver may be secured behind the shield to provide a quick means of continuity of fire. Many police also still use revolvers as their duty weapon due to revolvers' reliability and user friendliness.[1]

Loading and unloading

Front loading

The first revolvers were more front loading or muzzle loading. Rather than being loaded through the barrel, each chamber in the cylinder was rotated out of line with the barrel, and charged from the front with loose powder and a bullet. Usually, there was a loading lever attached to the bottom of the barrel that gave the user leverage to force the oversized lead ball into the chamber, which sealed it and held the ball and powder securely in place. The first practical revolvers were caplocks or cap and ball revolvers, because the caplock method of priming was the first to be compact enough to make a practical revolver feasible.

Fixed cylinder designs

In many of the first generation of cartridge revolvers (especially those that were converted after manufacture), the pin on which the cylinder revolved was removed, and the cylinder taken from the gun for loading. Later models used a loading gate at the rear of the cylinder that allowed one cartridge at a time to be accessed for loading, while a rod under the barrel could be pressed backwards to extract the fired case. Most revolvers using this method of loading are single action revolvers, although Iver Johnson produced double-action models with removable cylinders. The removable-cylinder design is employed in some modern "micro-revolvers" (usually in .22 caliber), in order to simplify their design. These weapons are small enough to fit in the palm of the hand.

The loading gate on the original Colt designs (and on nearly all single action revolvers since, such as the famous Colt Single Action Army) is on the right side, which may favor left-handed users; with the revolver held in the proper grip for shooting in the left hand, the cartridges can easily be ejected and loaded with the right.[2]

Since the cylinder in these revolvers is firmly attached at the front and rear of the frame, and since the frame is typically full thickness all the way around, fixed cylinder revolvers are inherently strong designs. Because of this, many modern large caliber hunting revolvers tend to be based on the fixed cylinder design.fixed cylinder revolvers can fire the strongest,most powerful cartridges,but a the price of being the slowest to load,and cannot,for obvious reasons,use speedloaders or moon clips.they can take speed strips,but one round at a time,and carrying them would be not for speed,but convienience of keeping ammunition together,and flatter.

Top break

A Webley Mk VI .455 calibre top-break service revolver

The next method used for loading and unloading cartridge revolvers was the top break design. In a top-break revolver, the frame is hinged at the bottom front of the cylinder. Releasing the lock and pushing the barrel down brings the cylinder up—this exposes the rear of the cylinder for reloading. In most top-break revolvers, the act of pivoting the barrel and cylinder operates an extractor that pushes the cartridges in the chambers back far enough that they will fall free, or can be removed easily.

Fresh rounds are then inserted into the cylinder, either one at a time or all at once with either a speedloader or a moon clip. The barrel and cylinder are then rotated back and locked in place, and the revolver is ready to fire. Since the frame is in two parts, held together by a latch on the top rear of the cylinder, top-break revolvers are relatively weak, and cannot handle high pressure rounds. Top-break designs are nearly extinct in the world of firearms, but they are still found in airguns.

One of the most famous "break top" revolvers is the Schofield Model 3, designed in the late 19th century and used by western outlaw Jesse James. Another notable design is the Enfield and Webley series of revolvers used by the British Armed Forces from the 1880s through the 1960s.

Top break revolvers in .22 rimfire and in .32 and .38 Smith & Wesson centerfire were popular civilian arms for both sporting purposes and self-defense from the late 19th century to the 1950s.

Swing out cylinder

The last and most modern method of loading and unloading is the swing out cylinder. The cylinder is mounted on a pivot that is coaxial with the chambers, and the cylinder swings out and down (to the left in most cases). An extractor is fitted, operated by a rod projecting from the front of the cylinder assembly. When pressed, it will push all fired rounds free simultaneously (as in top break models, the travel is designed to not completely extract longer, unfired rounds). The cylinder may then be loaded, singly or again with a speedloader, closed, and latched in place.

The pivoting part that supports the cylinder is called the crane; it is the weak point of swing-out cylinder designs. Using the method often portrayed in movies and television of flipping the cylinder open and closed with a flick of the wrist can in fact cause the crane to bend over time, throwing the cylinder out of alignment with the barrel. Lack of alignment between chamber and barrel is a dangerous condition- impeding the bullet's transition from chamber to barrel. This gives rise to higher pressures in the chamber, bullet damage, and the potential for an explosion if the bullet becomes stuck.

The shock of firing can also put a great deal of stress on the crane, as in most designs the cylinder is only held closed at one point, the rear of the cylinder. Stronger designs, such as the Ruger Super Redhawk, use a lock in the crane as well as the lock at the rear of the cylinder. This latch provides a more secure bond between cylinder and frame, and allows the use of larger, more powerful cartridges. Swing out cyinders are rather strong, but not as strong as fixed cylinders, and great care must be taken with the cylinder when loading, so as not to damage the crane.

Action

Single action

USFA US Pre-War Single Action Army at full-cock, ready to fire

In a single action revolver, the hammer is manually cocked, usually with the thumb of the firing or supporting hand. This action advances the cylinder to the next round and locks the cylinder in place with the chamber aligned with the barrel. The trigger, when pulled, releases the hammer, which fires the round in the chamber. To fire again, the hammer must be manually cocked again. This is called "single action" because the trigger only performs a single action, of releasing the hammer. Because only a single action is performed and trigger pull is lightened, firing a revolver in this way allows most shooters to achieve greater accuracy. Additionally, the need to cock the hammer manually acts as a safety.

Double action

Colt Anaconda .44 Magnum revolver
Colt Python .357 Magnum revolver

In double action (DA), the stroke of the trigger pull generates two actions: (1) the hammer is pulled back to the cocked position while the cylinder is being indexed to the next round, and then (2) the hammer is released to strike the firing pin. Thus DA means that a cocking action separate from the trigger pull is unnecessary; and every trigger pull will result in a complete cycle. This allows uncocked carry while also allowing draw-and-fire using only the trigger. A longer and harder trigger stroke is the trade-off, but this con can also be viewed as a pro (more drop-safe).

Most double action revolvers may be fired in two ways.

  1. The first way is single action, that is, exactly the same as a single action revolver; the hammer is cocked with the thumb, which indexes the cylinder, and when the trigger is pulled, the hammer is tripped.
  2. The second way is double action, that is, from a hammer-down position. In this case, the trigger first cocks the hammer and revolves the cylinder, and then trips the hammer at the rear of the trigger stroke, firing the round in the chamber.

Certain revolvers, called double action only (DAO), lack the latch that enables the hammer to be locked to the rear, and thus can only be fired in the double action mode. With no way to lock the hammer back, DAO designs tend to have bobbed or spurless hammers, and may even have the hammer completely covered by the revolver's frame (ie, shrouded or hooded). These are generally intended for concealed carrying, where a hammer spur could snag when the revolver is drawn. The potential reduction in accuracy in aimed fire is offset by the increased capability for concealment.

DA and DAO revolvers were the standard-issue sidearm of countless police departments for many decades. Only in the 1990s did the semiautomatic pistol begin to make serious inroads, after the advent of safe actions such as Glock's. The reasons for these choices are the modes of carry and use. Double action is good for high-stress situations because it allows a mode of carry in which "draw and pull the trigger" is the only requirement—no safety catch release or separate cocking stroke required. Although those seem simple to a person in calm circumstances, it is considered that less can go wrong with a simpler action when the user is highly stressed. This is a school of thought, not an immutable rule; some users would not make the same choice (preferring, e.g., cocked-and-locked carry), although they understand the logic.

Other

In the cap-and-ball days of the mid nineteenth century, two revolver models, the English Tranter and the American Savage “Figure Eight”, used a method whereby the hammer was cocked by the shooter’s middle finger pulling on a second trigger below the main trigger.

Iver Johnson made an unusual model from 1940 to 1947, called the Trigger Cocking Double Action. If the hammer was down, pulling the trigger would cock the hammer. If the trigger was pulled with the hammer cocked, it would then fire. This meant that to fire the revolver from a hammer down state, the trigger must be pulled twice.[3]

Use with suppressors

As a general rule, revolvers cannot be equipped with a sound suppressor ("silencer"), as there is usually a small gap between the revolving cylinder and the barrel which a bullet must traverse or jump when fired. From this opening, a rather loud report is produced even when a suppressor is installed on the end of the barrel of most revolvers. However, eliminating this problem would make the revolver a good weapon for suppressed use: in automatics, the action itself creates a significant amount of noise even if muzzle report is totally eliminated. A revolver, which does not cycle on its own and whose action is naturally quiet, does not present this problem.

A suppressible revolver design does exist in the Nagant M1895, a Russian military revolver used from 1895 through World War II. This revolver uses a unique cartridge that extends beyond the end of the bullet, and a cylinder that moves forward to place the end of the cartridge inside the barrel when ready to fire. This bridges the gap between the cylinder and the barrel, and expands to seal the gap when fired. While the tiny gap between cylinder and barrel on most revolvers is insignificant to the internal ballistics, the seal is especially effective when used with a suppressor, and a number of suppressed Nagant revolvers have been used since its invention.[4]

There is a modern revolver of Russian design, the OTs-38,[5] which uses ammunition that incorporates the silencing mechanism into the cartridge case, making the gap between cylinder and barrel irrelevant as far the suppression issue is concerned. The OTs-38 does need an unusually close and precise fit between the cylinder and barrel due to the shape of bullet in the special ammunition (Soviet SP-4), which was originally designed for use in a semi-automatic.

Additionally, the US Military experimented with designing a special version of the Smith and Wesson Model 29 for Tunnel Rats, called the Quiet Special Purpose Revolver or QSPR. Using special .40 caliber ammunition, it never entered service, at least officially.

Automatic revolvers

Double action revolvers use a long trigger pull to cock the hammer, thus negating the need to manually cock the hammer between shots. The disadvantage of this is the long, heavy pull that cocks the hammer makes the double action revolver much harder to shoot accurately than a single action revolver (although cocking the hammer of a double action reduces the length and weight of the trigger pull). There is a rare class of revolvers, the automatic revolver, that attempts to overcome this restriction, giving the high speed of a double action with the trigger effort of a single action.

The Webley-Fosbery Automatic Revolver was the first commercial example, introduced in 1901. It was recoil-operated, and the cylinder and barrel recoiled backwards to cock the hammer and revolve the cylinder. It was distinctive in that cam grooves were milled on the outside of the cylinder to provide a means of advancing to the next chamber—half a turn as the cylinder moved back, and half a turn as it moved forward. .38 caliber versions held 8 shots, .455 caliber versions 6. At the time, the few available automatic pistols were larger, less reliable, and more expensive. The automatic revolver was popular when it first came out, but was quickly superseded by the creation of reliable, inexpensive semi-automatic pistols.

In 1997, the Mateba company developed a type of recoil-operated automatic revolver, commercially named the Mateba Autorevolver, which uses the recoil energy to auto-rotate a normal revolver cylinder holding 6 or 7 cartridges, depending on the model. The company has made several versions of its Autorevolver, including longer barrelled and carbine variations, chambered for .357 Magnum, .44 Magnum and .454 Casull. The Pancor Jackhammer is a combat shotgun based on a similar mechanism to an automatic revolver. It uses a gas action to move the barrel forward (which unlocks it from the cylinder) and then rotate the cylinder and cock the hammer.

Six gun

A Six Gun is a revolver that holds six bullets. The cylinder in a six gun is often called a 'wheel', and the six gun is itself often called a 'wheel gun'.[citation needed] The classic six gun was commonly carried by Old West cowboys and gunfighters. A well-known example of the six gun is the Colt Single Action Army, or Peacemaker, in .45 Long Colt caliber. The six gun has many modern incarnations, such as the Ruger Vaquero and Beretta Stampede, as well as the currently produced Colt Single Action Army.

The basic operation of the six gun is:

  1. The hammer is cocked with the thumb, which rotates the cylinder to line up a new cartridge with the barrel, and positions the hammer for firing.
  2. The trigger is pulled, which causes the hammer to drop and sharply push the firing pin into the cartridge primer, firing the gun.
  3. The hammer must be cocked again for the next shot. This is called 'Single Action'.

Modern six guns are used commonly by Single Action Shooting enthusiasts in shooting competitions, designed to mimic the gunfights of the Old West, and for general target shooting and personal defense.

History

6-chambered wheel-lock revolver (Germany 1590)
.357 Magnum calibre Ruger Vaquero single-action revolver; modeled after the Colt Single Action Army

In the development of firearms, an important limiting factor was the time it took to reload the weapon after it was fired. While the user was reloading, the weapon was nearly useless, and an adversary might be able to take advantage of the situation and kill or wound the user. Several approaches to the problem of increasing the rate of fire were developed, the earliest being multi-barreled weapons which allowed two or more shots without reloading. The first revolvers were partly an attempt to improve on pepper-box type weapons, which used a revolving cylinder with one set of firing mechanisms, but which had multiple barrels as well. Firing through a single barrel saved the expense and weight of having the multiple barrels of the pepper-box.

The earliest example of a revolver is a revolving arquebus, produced by Hans Stopler in 1597.[6] Another early specimen, now in the Tower of London armories, is dated to the middle 1600s and attributed to John Dafte of London. This example, a flintlock, uses a single lock, with a flash pan for each of the six chambers. The cylinder is rotated by hand, and locks in place for firing. This was still not perfected, however, as it was apparently destroyed by a misfire.[7]

James Puckle patented a revolving chamber gun in 1718. This gun, which had a 1.25 inch bore (30 mm), was tripod mounted, and the 11-shot cylinder was operated by a hand crank. It is often cited as the first machine gun. By changing cylinders to reload (an early example of a speedloader), the gun was fired and reloaded to fire a total of 63 rounds in seven minutes. Elisha Collier patented a flintlock revolver in Britain in 1818, and significant numbers were being produced in London by 1822.

In 1836, Samuel Colt patented a revolver mechanism that led to the widespread use of the revolver. According to Samuel Colt, he came up with the idea for the revolver while at sea, inspired by the capstan winch, which had a ratchet and pawl mechanism on it, a version of which was used in his guns to rotate the cylinder. Revolvers proliferated largely due to Colt's ability as a salesman. Revolvers have remained popular to the present day in many areas, although in the military and law enforcement they have largely been supplanted by magazine-fed semi-automatic pistols such as the Colt M1911, especially in circumstances where reload time and higher cartridge capacity are deemed important.

Patents

Elisha Collier patented a flintlock revolver in Britain in 1818, and significant numbers were being produced in London by 1822. The origination of this invention is in doubt, as similar designs were patented in the same year by Artemus Wheeler in the United States and by Cornelius Coolidge in France. Samuel Colt received a British patent for his revolver in 1835 and an American patent (number 138) on February 25, 1836 for a Revolving gun, and made the first production model on March 5 of that year.

Another revolver patent was issued to Samuel Colt on August 29, 1839. The February 25, 1836 patent was then reissued as U.S. Patent RE00,124 entitled Revolving gun to Samuel Colt on October 24, 1848. This was followed by U.S. Patent 0,007,613 on September 3, 1850 for a Revolver, and by U.S. Patent 0,007,629 on September 10, 1850 for a Revolver. U.S. Patent 5,333,531 was issued to Roger C. Field for an economical device for minimizing the flash gap of a revolver between the barrel and the cylinder.

Notable brands and manufacturers

Gallery

See also

References

  1. ^ Taylor, Chuck (2009-08-29). "Why The Revolver Won’t Go Away". Tactical-Life.com. http://www.tactical-life.com/online/exclusives/commentary-why-the-revolver-wont-go-away/. Retrieved 2009-09-16. 
  2. ^ R.K. Campbell. "Tips For Lefties Shooting In a Right Handed World". GunWeek.com. http://www.gunweek.com/2000/lefties.html. Retrieved 2007-11-13. 
  3. ^ S. P. Fjestad (1992). Blue Book of Gun Values, 13th Ed.. Blue Book Publications, Inc.. ISBN 0-9625943-4-2. 
  4. ^ "Silenced 7.62 mm Nagant Revolver". Guns.connect.fi. 2000-09-18. http://guns.connect.fi/gow/nagant.html. Retrieved 2009-09-16. 
  5. ^ "OTs-38 silent revolver". Modern Firearms. http://www.modernfirearms.net/handguns/hg194-e.htm. Retrieved 2009-09-16. 
  6. ^ Roger Pauly (2004). Firearms: The Life Story of a Technology. Greenwood Publishing Group. ISBN 0313327963. 
  7. ^ Samuel Colt (1855). On the Application of Machinery to the Manufacture of Rotating Chambered-Breech Fire-Arms, and Their Peculiarities. W. Clowes. http://books.google/com. 

External links


Quotes

Up to date as of January 14, 2010
(Redirected to Revolver (film) article)

From Wikiquote

Revolver is a 2005 movie, written and directed by Guy Ritchie.

The film stars Jason Statham as Jake Green, Ray Liotta as Dorothy Macha, and André Benjamin (a.k.a. "André 3000") as Avi. It centers on a revenge-seeking confidence trickster whose weapon is a universal formula that guarantees victory to its user, when applied to any game or confidence trick. This is the third feature film by Ritchie which is centered on crime and professional criminals. It was released in UK theaters on September 22, 2005, but performed poorly at the box office.

Contents

Jake Green

There is something about yourself that you don't know. Something that you will deny even exists, until it's too late to do anything about it. It's the only reason you get up in the morning. The only reason you suffer the shitty boss, the blood, the sweat and the tears. This is because you want people to know how good, attractive, generous, funny, wild and clever you really are. Fear or revere me, but please, think I'm special. We share an addiction. We're approval junkies. We're all in it for the slap on the back and the gold watch. The hip-hip-hoo-fuckin' rah. Look at the clever boy with the badge, polishing his trophy. Shine on you crazy diamond, because we're just monkeys wrapped in suits, begging for the approval of others.

Macha

So how exactly did this one manage to disarm and overpower a four-time national bodybuilding champion? Drag him half a block, throw him over six-foot wall, and then fed him to his own gun?

Jake Green

One thing I've learned in the last seven years: in every game and con there's always an opponent, and there's always a victim. The trick is to know when you're the latter, so you can become the former.

Jake Green

Mr. Green in the elevator, after being convinced by his friends not to take the stairs: Now I've got to spend the next two minutes, shaking... and sweating... like a crack whore clucking for a fix... Should have taken the stairs... cause it's getting very... very tight in here.

Jake Green

Oh, I know you're still there... cause I can feel you dying. I can hear you tapping me... for a little nutrition. Now who's looking for a fix? It gets a little tight in here, do you? Well, you're not wrong... cause the walls are moving in. No food here. Not today, sunshine. My eyes are open and the restaurant's closed. Jog on. Slide off. Find someone else to fill your pipe. Someone, who won't see you coming... or know, when you're there.

Avi

The greatest con, that he ever pulled... was making you believe... that he is you.

Jake Green

Very funny, George. This one will make you laugh. [shoots George in the foot]

Jake Green: There is something about yourself that you don't know. Something that you will deny even exists, until it's too late to do anything about it. It's the only reason you get up in the morning. The only reason you suffer the shitty boss, the blood, the sweat and the tears. This is because you want people to know how good, attractive, generous, funny, wild and clever you really are. Fear or revere me, but please, think I'm special. We share an addiction. We're approval junkies. We're all in it for the slap on the back and the gold watch. The hip-hip-hoo-fuckin' rah. Look at the clever boy with the badge, polishing his trophy. Shine on you crazy diamond, because we're just monkeys wrapped in suits, begging for the approval of others.


Zach: Did you get anything from the old lady?

Jake Green: No.

Zach: Did you get anything from Horwitz?

Jake Green: No.

Zach: Why not?

Jake Green: Because he didn't have it.

Zach: Listen, pal. Either he pays or you pay.

Jake Green: I pay anyway.

Zach: Don't be a smartass.


Jake Green: I am rich. Seriously fucking rich.

Jake Green: Now I'm richer. A lot fucking richer.


Macha: What? He missed? Sorter never fucking misses.


Macha: What is this? Where were security?

French Paul: They gased them. We found them tied up.

French Paul: 12-tone permanent Eagle Safe, Mister D. It was impossible to break into.

Macha: Well, it wasn't fucking impossible to move, now, was it, Paul?

Macha: What did anyone take it for? We don't even use that safe, do we, Paul?

Macha: Paul?

French Paul: Not usually, no.

French Paul: Sam Gold's powder was in that. Came in yesterday.

Macha: No, Paul. You're wrong.

Macha: Try again.

Macha: You stupid motherfucker.


Macha: Why don't you just fucking rape me, Paul?


Macha: [to French Paul] Look at me! Does it look like I'm afraid of consequences? Fuck him!

Lord John: [in subtitles, to Fat Dan] Fuck him!

Macha: Fuck the consequences!

Lord John: Fuck the consequences!

Macha: Fuck them all!

Lord John: Fuck them all!


Sorter: Ch-check she's dead [calmly said to colleague after shooting an assassin in the neck, and then walking off to take care of the driver]

Quotes from the Movie that are quotes:

“The greatest enemy will hide in the last place you would ever look.”

—Julius Caesar 75 BC

“The only way to get smarter is by playing a smarter opponent.”

—Fundamentals of Chess 1883

“First rule of business, protect your investment.”

—Etiquette of the Banker 1775

“There is no avoiding war, it can only be postponed to the advantage of your enemy.”

—Niccolo Machiavelli 1502

“The only real enemy to have ever existed, is an eternal one.”

—The Road to Suicide, pg 1, line 1

“Your friends are close, but your enemy is closer.”

—The Road to Suicide, pg 1, line 2


Wiktionary

Up to date as of January 15, 2010

Definition from Wiktionary, a free dictionary

See also revolver

German

Wikipedia-logo.png
German Wikipedia has an article on:
Revolver

Wikipedia de

Noun

Revolver m. (genitive Revolvers, plural Revolver)

  1. revolver







Got something to say? Make a comment.
Your name
Your email address
Message