Rolls-Royce/Snecma Olympus 593: Wikis

Advertisements
  
  

Note: Many of our articles have direct quotes from sources you can cite, within the Wikipedia article! This article doesn't yet, but we're working on it! See more info or our list of citable articles.

Encyclopedia

From Wikipedia, the free encyclopedia

Olympus 593
Preserved Olympus 593 engine at the Imperial War Museum Duxford
Type Turbojet
National origin United Kingdom/France
Manufacturer Rolls-Royce Limited/Snecma
First run June 1966
Major applications Concorde
Number built 67
Developed from Rolls-Royce Olympus

The Rolls-Royce/Snecma Olympus 593 was a reheated (afterburning) turbojet which powered the supersonic airliner Concorde. Rolls-Royce Limited and Snecma developed the engine from the Rolls-Royce Olympus. Until Concorde's regular commercial flights ceased the Olympus turbojet was unique in aviation as the only afterburning turbojet powering a commercial aircraft.

Installed in Concorde and operating at Mach 2 it was the world's most efficient jet engine.[1]

Contents

Design and development

The Olympus 593 project was started in 1964, using the BAC TSR-2's Olympus 320 as a basis for development. Bristol Siddeley of the UK and Snecma Moteurs of France were to share the project. Acquiring Bristol Siddeley in 1966, Rolls-Royce continued as the British partner.[2] The early stages validated the basic design concept but many studies were required to achieve desired specifications, e.g.

  • The critical factor – fuel consumption
  • Pressure Ratio
  • Weight/Size
  • Turbine entry temperature

Initially, engineers studied using turbojets or turbofans, but the lower frontal cross-sectional area of turbojets in the end was shown to be a critical factor in achieving superior performance. The competing Russian Tu-144 initially used a turbofan, but quickly changed to a turbojet with considerable improvement in performance.[2]

Olympus-powered Concorde 216 (G-BOAF) on the final-ever Concorde landing, at Bristol, England

Rolls-Royce carried out the development of the original Bristol Siddeley Olympus and engine accessories, while Snecma was responsible for the variable engine inlet system, the exhaust nozzle/thrust reverser, the afterburner and the noise attenuation system. Britain was to have a larger share in production of the Olympus 593 as France had a larger share in fuselage production.

In June 1966 a complete Olympus 593 engine and variable geometry exhaust assembly was first run at Melun-Villaroche, Île-de-France, France. At Bristol, flight tests began using a RAF Vulcan bomber with the engine attached to its underside. Due to the Vulcan's aerodynamic limitations the tests were limited to a speed of Mach 0.98 (1,200 km/h). During these tests the 593 achieved 35,190 lbf (157 kN) thrust, which exceeded the requirements of the engine.[3]

In April 1967 the Olympus 593 ran for the first time in a high altitude chamber, at Saclay Île-de-France, France. In January 1968 the Vulcan flying test bed logged 100 flight hours, and the variable geometry exhaust assembly for the Olympus 593 engine was cleared at Melun-Villaroche for flight in the Concorde prototypes.

At 15:40 on the 2nd March 1969 Concorde prototype 001, captained by chief test pilot André Turcat, started its first take off run, with afterburners lit. The four Olympus 593 engines accelerated the aircraft, and after 4,700 feet (1.4 km) of runway and at a speed of 205 knots (380 km/h), captain Turcat lifted the aircraft off for the first time.

67 engines in the end were manufactured.[2]

Plans were drawn up for a quieter and more powerful version of the engine with an extra turbine section and a larger-diameter air compressor that would have eschewed the reheat and added sound-deadening; this would have improved efficiency across the board and permitted rather greater range and opened up new routes, particularly across the Pacific as well as transcontinental across America. However, the poor sales of Concorde meant that this plan for a Concorde 'B' was never put into practice.[4]

Technical description

A jet engine draws air in at the front and compresses it. The air then combines with fuel and the engine burns the resulting mixture. The combustion greatly increases the volume of the gases which are then exhausted out of the rear of the engine. The Olympus engine took this gas jet and passed it through straightening vanes - to obtain a laminar flow. This gas jet then entered the afterburning jet pipe where a ring of fuel injectors sprayed fuel onto the hot exhaust gases. The resulting combustion greatly improved thrust, although it also lead to high fuel consumption. The afterburner was thus only used at takeoff and from just below Mach 1 up to Mach 1.7, the engine 'supercruised' above that speed.

The afterburning section was longer than the engine itself (as was the case with all early turbojets) but the thrust of the Olympus 302 rose to 30,610 lbf (136 kN).

Advertisements

Inlet system

Concorde's ramp system schematics
Concorde's ramp system
G-AXDN, Duxford, close up of engines, with the scalloped thrust reversers prominent.

Although not strictly considered part of the engine, the variable engine inlet system was vital to the Olympus 593 on Concorde as supersonic airflow at the engine face could create shockwaves that would lead to engine surge and failure. The intake featured variable ramps which altered the intake area which slowed the intake air from supersonic to subsonic speed. This was achieved by positioning the ramps such that shockwaves were created at the inlet, air passing through these shockwaves was slowed. The inlet air was further decelerated as the intake area increased closer to the engine (speed of air flow decreases as area increases.) Any excess air was expelled through doors on the underside of the nacelle and some intake air was bypassed around the engine and mixed with the exhaust - to increase thrust and keep the engine cool. The TSR-2 had used a semicircular design with the shock front adjusted by a translating centrebody to overcome the same problem.[5]

The overall pressure ratio of the air by the inlet system as well as the compression within the engine was as high as 80:1 at supersonic speeds.[6] This gave the engine world-beating efficiency.

Compression section

The engine is a twin spool engine with 7 compressor stages on each spool. Unusually, the last 4 compressor stages were made of nickel alloy due to the high pressures and thus high temperatures in supersonic flight- ordinarily, nickel alloy is only used on the turbine sections of jet engines.[7]

Exhaust nozzle

The variable geometry exhaust nozzle consisted of two "eyelids" which varied their position in the exhaust flow dependent on the flight regime, for example when fully closed (into the exhaust flow) they acted as thrust reversers, aiding deceleration from landing to taxi speed.

Variants

  • 593 - Original version designed for Concorde
    • Thrust : 20,000 lbf (89 kN) dry / 30,610 lbf (136 kN) reheat
  • 593-22R - Powerplant fitted to prototypes. Higher performance than original engine due to changes in aircraft specification.
    • Thrust : 34,650 lbf (154 kN) dry / 37,180 lbf (165 kN) reheat
  • 593-610-14-28 - Final version fitted to production Concorde
    • Thrust : 32,000 lbf (142 kN) dry / 38,050 lbf (169 kN) reheat

Specifications (Olympus 593 Mk 610)

Data from: [8][9]

General characteristics

  • Type: Turbojet
  • Length: 4039 mm (159 in)
  • Diameter: 1212 mm (47.75 in)
  • Dry weight: 3175 kg (7,000 lb)

Components

  • Compressor: Axial flow, 7-stage low pressure, 7-stage high pressure
  • Combustors: Nickel alloy construction annular chamber, 16 vapourising burners, each with twin outlets
  • Turbine: High pressure single stage, low pressure single stage
  • Fuel type: Jet A1

Performance

Control system

  • World's first FADEC control system

Jetpipe

  • Straight pipe with pneumatically operated convergent nozzle
  • Single ring afterburner
  • 'Eyelids' which act as variable divergent nozzles/thrust reversers

See also

References

External links


Advertisements






Got something to say? Make a comment.
Your name
Your email address
Message